DC Input - Bipolar Output Switcher PC Boards for Small Projects

Construction information for DIY projects, including the MS Mid Side Matrix, Elliptic Equalizer, Mastering Console, Phono Transfer System, Insert Switcher and the Dual Class-A Amplifier. You can post your baby pictures here.
Post Reply
User avatar
mediatechnology
Posts: 5726
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

DC Input - Bipolar Output Switcher PC Boards for Small Projects

Post by mediatechnology »

For evaluation I'm ordering a couple of small PC board bipolar output switchers for use with DC wall-warts or USB power.

https://www.amazon.com/gp/product/B0752TRXDC

Image

https://www.amazon.com/gp/product/B07SFLVGMJ

Image

There is a third one available but it has no mounting holes which I consider a serious limitation.

We'll see if they're quiet enough...
User avatar
AnalogJoe
Posts: 180
Joined: Mon Dec 24, 2018 3:11 pm

Re: DC Input - Bipolar Output PC Boards for Small Projects

Post by AnalogJoe »

mediatechnology wrote: Sat Nov 02, 2024 6:48 am
We'll see if they're quiet enough...
If not, you can always spend tons on LC filtering.... :lol:
Bonum certamen certavi, cursum consumavi, fidem servavi.
User avatar
mediatechnology
Posts: 5726
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: DC Input - Bipolar Output PC Boards for Small Projects

Post by mediatechnology »

At least these, being PC boards, don't have to go in a hiccup mode to meet some dubious efficiency requirement.

That killed the otherwise excellent Meanwell triple output supply when they went from the P25A-series to the "green" GP25A.
User avatar
mediatechnology
Posts: 5726
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: DC Input - Bipolar Output PC Boards for Small Projects

Post by mediatechnology »

This one looks very promising. Still running some tests. The output ripple is low when preloaded at about 60 mA. The sweet spot for ripple is either 5V or 12V in. At 15V input over a narrow range ripple is higher: It looks like it's trying to makeup its mind whether to boost or buck. When unloaded its in hiccup mode.

The real test is to hook it up to a phono preamp.

https://www.amazon.com/gp/product/B0752TRXDC

Image
User avatar
mediatechnology
Posts: 5726
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: DC Input - Bipolar Output PC Boards for Small Projects

Post by mediatechnology »

https://www.amazon.com/gp/product/B0752TRXDC

Image

The above is the "DROK" brand switcher.
I used two 220Ω loads across the +15 and -15V rails to load it in 68 mA.
The specified minimum is load 30 mA but >60 mA yielded better results.
The input supply was a linear bench supply.
The input and output grounds are not galvanically isolated.

Some ripple oscillograms:

Image
DROK Switcher Ripple 5V 460mA Input 68mA Load Eff 88.6%

Image
DROK Switcher Ripple 12V 200mA Input 68mA Load Eff 85%

Image
DROK Switcher Ripple 24V 100mA Input 68mA Load Eff 85%

The RMS ripple over a 4 MHz bandwidth is <7mV; at 100 kHz BW <3 mV.

The second supply in the original post has much higher ripple and I didn't test it.
User avatar
mediatechnology
Posts: 5726
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: DC Input - Bipolar Output Switcher PC Boards for Small Projects

Post by mediatechnology »

I scanned the small leaflet that came with the DROK supply and created a data sheet.

The note for the ripple specification "on bare mental" is something I've never seen before. :lol:

Image

PDF: https://proaudiodesignforum.com/images/ ... asheet.pdf
Post Reply